Thermal Performance Improvement and Contamination Control Strategies in an Operating Room

Authors

  • Fu-Jen Wang National Chin-Yi University of Technology
  • Indra Permana National Chin-Yi University of Technology,
  • Dibakar Rakhsit Centre for Energy Studies, Indian Institute of Technology Delhi, India
  • Riza Siti Azizah National Chin-Yi University of Technology

DOI:

https://doi.org/10.15377/2409-5826.2021.08.4

Keywords:

Operating Room, Thermal Performance, Contamination Control, Field Measurement, Computational Fluid Dynamics

Abstract

Operating room is a cleanroom that provides thermal comfort and good indoor air quality (IAQ) to support the surgery process. The heating, ventilation, and air conditioning (HVAC) system plays a critical role for the health protection regarding to IAQ, i.e., thermal performance, air changes per hour, pressurization, filtration, air distribution, etc. However, HVAC system in the operating room is operated for 24 hours year-round with intensive energy consumption. Energy-efficient approaches for the HVAC system is also quite challenging in term of contamination control to meet the standards specifications. In this study, a full-scale operating room was carried out through field measurements and numerical analysis extensively. Computational Fluid Dynamic (CFD) simulation has been carried out and verified with field measurement data. Thermal comfort performance along with temperature distribution and velocity profile have been simulated extensively. The energy-efficient approach by reducing the face velocity of the HEPA filter was examined which is done by reducing the velocity from 0.4, 0.3, 0.2 (m/s) for energy-saving concern but still need to meet the thermal performance and minimum contamination control requirement. The results reveal how the potential of HVAC systems to control air contamination, a comfortable thermal environment for occupants and the possibility of energy-efficient approaches in the operating room.

References

Stern RA, Koutrakis P, Martins MAG. Characterization of hospital airborne SARS-CoV-2. Respir Res 2021; 22: 73. https://doi.org/10.1186/s12931-021-01637-8

Nastase I, Croitoru C, Vartires A, Tataranu L. Indoor environmental quality in operating rooms: European standards review with regard to Romanian guidelines. Energy Procedia 2016; 85: 375-82. https://doi.org/10.1016/j.egypro.2015.12.264

United States Environmental Protection Agency (2021). Improving Indoor Air Quality. https://www.epa.gov/indoor-air-quality-iaq/improving-indoor-air-quality accessed on August 25, 2021.

ANSI/ASHRAE Standard 170-2017, Ventilation of health care facilities. Atlanta, GA.

ANSI/ASHRAE Standard 62.2-2019, Ventilation and acceptable indoor air quality. Atlanta, GA.

Aganovic A, Cao G, Stenstad LI, Skogås JG. Impact of surgical lights on the velocity distribution and airborne contamination level in an operating room with laminar airflow system. Build Environ 2017; 126: 42-53. https://doi.org/10.1016/j.buildenv.2017.09.024

Chow TT, Lin Z, Bai W. The integrated effect of medical lamp position and diffuser discharge velocity on ultra-clean ventilation performance in an operating theatre. Indoor built environ 2006; 15: 315-331. https://doi.org/10.1177/1420326X06067802

Sadeghian P, Wang C, Duwig C, Sadrizadeh S. Impact of surgical lamp design on the risk of surgical site infections in operating rooms with mixing and unidirectional airflow ventilation: A numerical study. J Build Eng 2020; 31: 101423. https://doi.org/10.1016/j.jobe.2020.101423

Liu Z, Zhang M, Cao G, Tang S, Liu H, Wang L. Influence of air supply velocity and room temperature conditions on bioaerosols distribution in a class I operating room. Build Environ 2021; 15: 108116. https://doi.org/10.1016/j.buildenv.2021.108116

Wang FJ, Lai CM, Cheng TJ, Liu ZY. Performance evaluation of indoor environment parameters for an unoccupied operating room. ASHRAE Trans 2011; 117: 557-564.

Wang FJ, Hung J, Chen Y, Hsu C. Performance evaluation for operation rooms by numerical simulation and field measurement. Int J Vent 2017; 16: 189-99. https://doi.org/10.1080/14733315.2017.1299515

Sun Z, Wang S. A CFD-based test method for control of indoor environment and space ventilation. Build Environ 2010; 45: 1441-7. https://doi.org/10.1016/j.buildenv.2009.12.007

Bombač M, Novak G, Mlačnik J, Četina M. Extensive field measurements of flow in vertical slot fishway as data for validation of numerical simulations. Ecolog Eng 2015; 84: 476-84. https://doi.org/10.1016/j.ecoleng.2015.09.030

Peng S, Chen Q, Liu E. The role of computational fluid dynamics tools on investigation of pathogen transmission: Prevention and control. Sci Total Environ 2020; 31: 142090. https://doi.org/10.1016/j.scitotenv.2020.142090

Chung KC, Hsu SP. Effect of ventilation pattern on room air and contaminant distribution. Build Environ 2001; 36: 989-998. https://doi.org/10.1016/S0360-1323(00)00051-2

Cui S, Cohen M, Stabat P, Marchio D. CO2 tracer gas concentration decay method for measuring air change rate. Build Environ 2015; 84: 162-169. https://doi.org/10.1016/j.buildenv.2014.11.007

International Organization for Standard (ISO). ISO 14644-1, Cleanroom and Associated Controlled Environments-Part 1: Classification of air cleanliness by particle concentration. Vernier, Geneva, Switzerland, 2015.

U.S. General Services Administration. U. S. Federal Standard 209E, Airborne Particulate Cleanliness Classes in Cleanrooms and Clean Zones. Washington, USA, 1992.

ANSYS. Ansys fluent, Workbench 2020 R2. www.ansys.com

Peng S, Chen Q, Liu E. The role of computational fluid dynamics tools on investigation of pathogen transmission: Prevention and control. Sci Total Environ 2020; 31: 142090. https://doi.org/10.1016/j.scitotenv.2020.142090

Minnesota Department of Health United States. Carbon dioxide (CO2). https://www.health.state.mn.us/communities/environment/air/toxins/co2.html accessed on June 15, 2021.

Brohus H, Balling KD, Jeppesen D. Influence of movements on contaminant transport in an operating room. Indoor air 2006; 16: 356-372, 2006. https://doi.org/10.1111/j.1600-0668.2006.00454.x

Suresh K, Regalla SP. Effect of mesh parameters in finite element simulation of single point incremental sheet forming process. Proc Mat Sci 2014; 6: 376-382. https://doi.org/10.1016/j.mspro.2014.07.048

Downloads

Published

2021-09-30

How to Cite

1.
Wang F-J, Permana I, Rakhsit D, Azizah RS. Thermal Performance Improvement and Contamination Control Strategies in an Operating Room. J. Adv. Therm. Sci. Res. [Internet]. 2021Sep.30 [cited 2021Oct.16];8:30-4. Available from: https://www.avantipublishers.com/jms/index.php/jatsr/article/view/1061

Issue

Section

Articles